Appliance Error Code Guide Codes, causes & fix order
Washers · Samsung

Samsung Washer Error Code 1E / 1C

1E is the code that appears when the machine stops halfway through a fill, or when it keeps filling after it should have stopped. The washer cannot see the water level, and the fix is usually a hose rather than a sensor.

Checked against Samsung support documentation Updated 17 November 2026 8 min read

The short answer

  • 1E / 1C — the water level sensor is reporting a level the board cannot use.
  • Most common cause: the pressure hose is kinked, fallen off, blocked with detergent sludge, or the air chamber on the tub is clogged.
  • Second: the sensor's connector is loose or corroded, or the sensor has failed.
  • Also check for water in the base — Samsung groups this code with its leak codes in some markets.

What the code is measuring

These washers do not measure water with a float. A small pressure sensor sits at the top of the cabinet connected by a thin tube to an air chamber at the bottom of the tub. As water rises, it compresses the air in the chamber and the tube, and the sensor converts that pressure into a level. 1E means the pressure signal does not match what the board expects — too little, too much, or nothing at all.

That design explains why the fault behaves the way it does. If the tube is disconnected the sensor reads the room, so the machine fills forever. If the air chamber is blocked with sludge the sensor reads a level that never changes, so the machine overfills or stops early. If the sensor itself dies, the reading is nonsense and the cycle stops.

Check order

  1. Unplug the machine and drain it before anything else. 1E can leave a drum full of water.
  2. Look for water under the machine and inside the base. A leak into the base is part of this code family on Samsung documentation.
  3. Find the thin pressure hose at the top of the tub — usually a clear or grey tube running from the sensor to a chamber on the tub. Check it is seated at both ends and not kinked or split.
  4. Blow through the hose gently or run water through it. A blocked tube gives a level that does not change. Detergent sludge and lint are the usual blockage.
  5. Clean the air chamber where it meets the tub. On top loaders it is reachable once the rear panel is off; on front loaders it is under the top cover.
  6. Check the sensor connector for corrosion and pushed-back pins, then reseat it.
  7. Run a short cycle and watch whether the drum fills to a sensible level. If it does and the code is gone, the hose or chamber was the fault.
Unplug before opening the cabinet, and never work on a machine that has water in the base. Water and mains voltage share that space. If the base is wet, find and fix the leak before powering the machine again.

What it points to

PartSignatureAction
Pressure hoseLoose, split, kinked or full of sludgeClean or replace — the cheapest fix here
Air chamberBlocked at the tub connection; level never changesClean
Sensor connectorGreen corrosion, loose pinsClean and reseat
Water level sensorHose and chamber proven clear, reading still wrongReplace
Inlet valveMachine overfills even after the hose is clearedTest and replace if it does not close
Control boardSensor and wiring test correct, reading still wrongLast resort

Repair or replace

A hose clean costs nothing, and a sensor is a modest part. If the machine is older and the fault follows a leak into the base, the honest question is whether the drum bearing and the board have also been affected — water in the base damages both. The cost formula is the way to judge that without invented prices.

Frequently asked questions

Why does 1E appear only on some cycles?

Because the level check only runs during fill. A partly blocked hose reads correctly at high level and wrongly at low level, so only the cycles that use a low fill trip the code.

My Samsung shows 1E and will not drain — is it two faults?

Usually one. If the board believes the drum is already full it may refuse to spin or drain. Fix the level fault first.

Can too much detergent cause 1E?

Indirectly, yes. Excessive foam and sludge block the air chamber and the hose. Use the recommended amount for your water hardness.

Sources

  1. Samsung support — washing machine information and error codes, including the 1E / 1C water level entry (US, UK and Philippines support pages), accessed 17 November 2026.
  2. Samsung service documentation on the pressure sensor, air chamber and inlet valve circuit.
  3. Editorial review against the parts trade: pressure hose and chamber blockage patterns on Samsung top and front loaders.

General information only. Sensor type, cabinet layout and code variants differ by model and market. Confirm against your machine's documentation, and unplug before opening any panel.