Appliance Error Code Guide Codes, causes & fix order
Washers · LG

LG Washer Error Code LE

LE looks like a leak code and is not one. It appears when the machine asks the drum to move and the drum does not — which is either a load problem you can fix in a minute or an electrical fault that needs a meter.

Checked against LG support documentation Updated 17 November 2026 8 min read

The short answer

  • LE — the drum could not turn as commanded. On LG machines this is a motor or load fault, not a leak.
  • First: take the load out, turn the drum by hand, and try a smaller load.
  • Second: look for a jam between the drum and the tub — a bra wire, a coin, a small item.
  • Third: hall sensor, motor harness, then the board.

What LE is measuring

A direct-drive LG washer has no belt: the motor is on the back of the drum. The control board knows the rotor position from a hall sensor and drives the stator in step with it. LE is set when the commanded rotation does not match the measured rotation — the motor is stalled, or the drum is too heavy to accelerate, or the sensor is giving a reading the board cannot use.

That is why the code appears most often at the start of a spin. It takes the most torque to accelerate a wet load from rest.

The order to check

  1. Unplug the machine and drain it if there is water in the drum.
  2. Remove the load entirely and turn the drum by hand through a full rotation. It should turn with light, even resistance. A stiff spot or a grinding feel points at a jam or a bearing.
  3. Look between the drum and the door seal for a small item, and check the pump filter for something that has been recirculating.
  4. Run an empty quick cycle. If it completes, the fault was the load — a single duvet, a bath mat or a heavy pair of jeans can do it on its own.
  5. If LE returns empty, check the motor connector and the harness at the back of the drum for damage, then test the hall sensor.

The load patterns that cause it

LoadWhy it trips LEWhat to do
One duvet or blanketAbsorbs water into one lump and cannot distributeWash with two towels to balance it
Bath mat with a rubber backingHeavy, and sticks to the drumWash separately on a low spin
Overloaded drumNo room to tumble, so the load rides with the drumFill to about three quarters at most
Very small loadCannot balance for the spinAdd a couple of items
Machine not levelLoad drifts to one side every cycleLevel the feet and lock them
Unplug before reaching into the drum or removing the back cover. On direct-drive machines the rotor sits behind a cover and can move as soon as power returns. Drain the water before tilting or opening anything.

What it points to

FindingPartNotes
Drum turns freely, code only with big loadsNoneLoad habit, not a repair
Drum stiff at one pointJam or bearingRemove the item; a bearing is a major repair
Drum spins by hand, no motion when commandedMotor harness, hall sensor or statorTest the sensor first — it is the cheaper part
Rotor loose or rubbingRotor bolt or bearingStop using the machine; damage spreads
Code changes between LE and UEBalance and driveFix the level and the load first

Repair or replace

If the answer is "rearrange the load", LE costs nothing. If it is a hall sensor or a harness, it is a modest repair. If the drum bearing has gone, the drum and tub usually come as an assembly on these machines, and that changes the decision — see repair or replace and what a washer repair involves.

Frequently asked questions

LE appears at the end of the cycle — is that the same fault?

Usually the final spin. The load has shifted or the machine cannot balance it. Redistribute and use a lower spin speed.

My LG shows LE and UE together. Which do I fix?

Balance first: level the machine, split the load, retry. If both codes still appear on an empty drum, the drive circuit needs testing.

Can a worn belt cause LE?

On belt-drive LG models a slipping or broken belt produces the same symptom. Check the belt before the motor.

Sources

  1. LG support — washing machine error code guidance for the LE / locked motor family, accessed 17 November 2026.
  2. Service documentation on direct-drive stator, rotor and hall sensor circuits.
  3. Editorial review against the parts trade: load-related LE complaints versus genuine drive faults.

General information only. Motor type, drive system and code wording differ by model. Confirm against your machine's documentation and unplug before opening the cabinet.