The short answer
- Cheap and quick: filter clean, hose reroute, inlet screen clean, levelling, door seal, drain pump, inlet valve.
- Moderate: door lock, pressure switch, suspension rods, heating element, board on some models.
- Expensive: drum bearings and spider, outer tub, motor and module on direct-drive machines.
- You influence the bill by noting the model and code, doing the free checks first, and asking for a parts-and-labour split.
Why prices differ, without quoting any
This site does not publish repair prices, because a figure that is right in one city is wrong in the next country. What can be compared across markets is the structure of a washer repair bill, and it has five parts:
- Call-out and diagnosis. A fixed attendance fee, sometimes credited against the repair.
- Part cost. Original manufacturer part versus a pattern part — often a factor of two, and not always a factor of two in reliability.
- Access labour. Some parts are behind one panel; some need the machine out, the top off and the drum lifted.
- Guarantee. A repair with a 12-month guarantee costs more than one with none, and is usually the better buy.
- Investigation. Whether the technician finds the cause or clears the code. This is the line item owners most often try to remove, and the one that prevents a repeat visit.
The jobs, by what they involve
| Job | What is involved | Codes it resolves | Owner-doable? |
|---|---|---|---|
| Filter clean / hose reroute | Open the filter door, drain, clean, check the run | 5E, OE, F21, no-code drain faults | Yes |
| Inlet screen clean | Hoses off, screens out, rinse, refit | 4E, IE | Yes |
| Levelling and feet | Adjust feet, lock nuts | UE, Ub, vibration | Yes |
| Door seal | Clamp ring off, seal replaced, ring refitted | Leaks, dE in some cases | Yes, with care |
| Drain pump | Panel off, hoses released, pump swapped | 5E, OE, F21, E25 on dishwashers | Yes on many front loaders |
| Inlet valve | Top or back panel, valve block swapped | 4E, IE | Yes, unplugged and taps off |
| Door lock | Door ring or front panel, lock assembly | dE, dC | Possible; alignment matters |
| Pressure switch / tube | Top panel, tube and switch access | LC, 5E on empty drum | Diagnosis first |
| Suspension rods | Top off, rods out in a set | UE on top loaders | Moderate |
| Heating element | Rear or front access depending on model | No-heat faults | Moderate |
| Control board | Panel, connectors, configuration | Multiple, after parts are proven | No |
| Drum bearing / spider | Full strip-down, drum out, bearing press | Rumble, knock, rust streaks | No |
The jobs that are worth doing yourself
Filter cleaning, hose checks, inlet screens, levelling and door seals need no specialist tools and no mains work beyond unplugging. A drain pump on a front loader is also realistic: it is a hose-clamp and connector job, and the model-specific pump is available from parts suppliers.
What is not realistic at home: anything that requires the drum to come out, the motor module, or the control board configuration. Those need a press, a service tool, or both.
Before the technician arrives
- Write down the code and the full model number from the rating plate. It saves the first ten minutes and often the part being wrong.
- Do the free checks so you can tell them what you have already ruled out.
- Clear the machine's surroundings — access to the back and sides is part of what you are paying for.
- Note when it happens — programme, temperature, load type. A code that only appears on a spin is different from one that appears on every fill.
- Ask for the parts-and-labour split in the quote, and whether the diagnosis is included.
When the bill decides it
Once you have a real quote, put it against the price of a comparable new machine using the formula in repair or replace. The rule of thumb — repair below half the price of new, and only with at least two more years of life left — holds across markets because it compares two numbers you actually have.
Frequently asked questions
Is a pattern part a bad idea?
Not necessarily. Many pattern pumps and valves are made in the same factories as the original. Where it matters is seals and electronics, where fitting quality decides how long the repair lasts.
Why is a bearing repair so expensive?
Because the drum has to come out of the cabinet and the bearing is pressed into the tub. The part is cheap; the labour is a half or full day, which is why age decides this repair more than anything else.
Should I accept a "board replacement" quote without a test?
Ask what was tested before the board was named. If the answer is only the code, get a second opinion — codes report symptoms, and a board is the most expensive way to guess.
Sources
- Editorial analysis of parts-trade cost structure: part versus labour weight for common washer jobs.
- Manufacturer service documentation on access procedures for pumps, valves, locks and drum assemblies.
- Consumer repair-rights and repairability material published by manufacturers and national consumer bodies, accessed 16 November 2026.
General guidance only, with no prices. Repair costs depend on country, brand, part availability and labour rates. Confirm the diagnosis before authorising work, and leave mains wiring, motor modules and drum work to a qualified technician.