The short answer
- F21 — long drain. The pump ran and the water level did not come down within the allowed time.
- Most common cause: a blocked pump filter or coin trap, or a drain hose that is kinked or pushed too far into a standpipe.
- Do this first: empty the drum, clean the filter, and check the hose is not sealed or jammed into the drain.
- If it returns with an empty drum: the pressure switch or its hose is reporting water that is not there.
What F21 reports
Whirlpool's code family is built from letters and numbers that describe a system and a fault — F for a function, E for an electronic fault, with a number for the specific condition. F21 sits in the drain group: the machine energised the pump, waited, and the level sensor still read water.
On Whirlpool top loaders — the VMW and Cabrio-style platforms sold under Whirlpool, Maytag and Roper badges — the drain path includes a pump with a removable filter or a coin trap, and a drain hose that must be routed into a standpipe or laundry tub without being sealed. On front loaders the pump and filter are behind the lower front panel.
The check order
- Empty the drum. On a top loader, lower the drain hose into a bucket below the drum and let it siphon. On a front loader, use the small drain hose next to the filter.
- Clean the filter or coin trap. Front loaders have a screw-out filter behind the lower panel; top loaders vary, and some use a small clean-out access on the pump body. Expect hair, lint, coins and a missing sock.
- Check the hose run. A kink behind the machine, a hose pushed flat, or a hose inserted too deep into a standpipe that is sealed with tape are all common. There must be an air gap.
- Check the standpipe or tub drain. If the discharge point is blocked or slow, the water backs up and F21 appears even though the pump is fine.
- Listen to the pump. Run a drain and spin. A hum with no flow means a jammed impeller; silence means no supply to the pump; a working pump with a slow drain means a restriction downstream.
- Pressure switch and hose. F21 on an empty drum, within seconds, is a sensing fault. Check the thin tube from the switch to the tub for water and the switch itself for a stuck contact.
Where F21 sits in the Whirlpool code family
| Code | Meaning | First check |
|---|---|---|
| F21 | Long drain — water did not leave in time | Filter, hose, pump |
| F9 E1 | Long drain associated with excess suds | Detergent dose, rinse, foam |
| F20 | No water detected during fill | Taps, inlet screens |
| F1 E1 / F1 E2 | Control board communication faults | Harness, connectors |
| PF | Power failure interrupted the cycle | Reset and restart |
Codes differ between platforms, and Whirlpool has sold the same code letters under several brands. Treat the table as a map, and confirm against the tech sheet behind the console or the toe grille of your machine.
What it points to
Filter, hose, standpipe, pump, pressure switch, board — in that order. A pump is only the answer once the path before and after it is proven clear, because a pump that is asked to move water against a blockage sounds exactly like a failing pump.
Repair or replace
Most F21 faults end in a free clean-out. A drain pump on a top loader is a modest part and a reasonable repair. If the machine also has bearing noise or a leaking tub seal, the combination is usually the point where repair or replace becomes a real question rather than a website's opinion.
Frequently asked questions
Can I use the machine with F21 if I bail the water out?
You can finish rescuing the load, but the machine will not spin a full drum, and repeated attempts strain the suspension. Fix the drain path first.
Why does F21 appear only on the final spin?
Because the final drain has the most water and the tightest time window. A partial restriction passes the earlier drains and fails the last one.
Does F21 mean the pump is dead on a Whirlpool front loader?
Not usually. Front loaders are more sensitive to a filter that is not screwed in fully, because the pump loses prime. Check the filter seal before the pump.
Sources
- Whirlpool Support — washer error code guidance for F21 and the drain filter cleaning procedure (whirlpool.com support sections), accessed 16 November 2026.
- Whirlpool service documentation for drain timing and pressure switch behaviour on top-load platforms.
- Editorial review against the parts trade: pump and filter failure patterns across Whirlpool-branded top and front loaders.
General information only. Code families and filter locations differ between Whirlpool platforms and brands. Confirm against the tech sheet for your model and unplug before opening the pump area.