The short answer
- E15 — water is standing in the base tray and has lifted the leak float. The machine will not run again until it is dry.
- It is a symptom, not a part failure: the water came from the door seal, an internal hose, the inlet valve, the pump housing or the sump.
- Do this first: unplug, drain the base, dry it, and run a short cycle with paper towels under the front to see where water appears.
- Do not just reset it — a reset with the leak unfixed means water on your kitchen floor next.
What E15 actually is
Under the tub of every Bosch dishwasher is a shallow base tray with a float switch — a polystyrene float on a lever. Its only job is to detect water where water should never be. If a leak of any kind reaches the tray, the float lifts, the switch closes and the control stops the machine with E15.
Three consequences follow from that design:
- The sensor is almost never the fault. A failed float switch is rare; water under the tub is not.
- The leak may be tiny. A drip per cycle accumulates over weeks until the tray fills. Owners often report E15 "out of nowhere" after months of a small leak.
- Resetting without fixing it works once. The base dries, the code clears, and the tray fills again — often until water reaches the floor or the neighbouring cabinet.
Where the water comes from
| Source | How to spot it | Weight of the repair |
|---|---|---|
| Door seal and corners | Water tracks down the inner door, damp at the front corners | Modest — seal replacement |
| Inlet hose inside the machine | Damp along the left side, near the water valve | Modest |
| Water inlet valve | Drip at the valve body when filling | Modest |
| Sump / pump housing seals | Water under the centre, more during drain | Moderate |
| Circulation pump seal | Water under the centre, worse during wash | Moderate |
| Over-sudsing | Foam visible in the tub, water at the door base | Free — change detergent dose |
Bosch designs vary: the entry-level and mid-range models share a base tray layout, while the flexible-zone and fully integrated ranges differ in where the inlet valve sits. The technique below works on all of them because the tray is in the same place.
Draining the base
- Unplug the dishwasher and shut the water supply if there is a tap under the sink.
- Remove the standing water in the tub first with a sponge or a shallow cup — the sump holds more than you expect.
- Tilt carefully. Pull the machine out and tip it onto towels, first one way then the other, so the base water runs to the front edge. Bosch units are heavy; get help if you need it, and never tip a machine onto its front panel.
- Sponge out the rest through the side access where the model allows, and dry the tray with a cloth.
- Power-cycle and run a short programme with paper under the front edge.
Finding the leak without stripping it down
The trick is to make the leak visible in stages. Dry everything, then:
- Run a rinse-only programme with no detergent and watch the front corners. Damp there is the door seal.
- Run a normal wash, empty, and look underneath with a torch after five minutes: filling-phase leaks point at the inlet valve and hose, washing-phase leaks at the circulation pump or sump.
- Watch during the drain phase: leaks that only appear then come from the drain pump, its housing or the sump seal.
- Look inside the tub for foam: a suds leak is not a seal failure, and it clears with the right detergent dose and a hot rinse.
Parts that end an E15
Door seal, inlet hose, inlet valve, sump seal kit, circulation pump seal, and — least often — the float switch itself. Most Bosch spares are model-specific: the full model number (usually on the inner edge of the door or the side of the tub) is needed before any seal or hose can be matched.
Repair or replace
A door seal or internal hose is a modest repair and clearly worth it. Pump and sump seals are moderate, and a technician can do them in an hour on most models. What makes E15 expensive is ignoring it: water in the base, a corroded control and a warped base plate turn a seal job into a write-off. Repair or replace covers the judgement if you are already at that stage.
Frequently asked questions
Can I use the dishwasher after clearing E15?
Only after you have found the leak, or at least confirmed the machine stays dry through a full cycle with paper underneath. A cleared code is not a fixed leak.
Why does E15 appear only sometimes?
Because a slow leak takes several cycles to fill the tray. The code arrives when the water reaches the float, not when the leak starts.
Is E15 the same as E24?
No. E24 is a blocked drain path — water that will not leave the tub. E15 is water that has already left and reached the base. Different faults, different checks.
Sources
- Bosch Home Appliances Support — dishwasher error code guidance for E15 and the leak detection system (bosch-home.com support sections), accessed 16 November 2026.
- Bosch service documentation on the base tray float switch, water inlet path and pump seals.
- Editorial review against the parts trade: door seal, inlet valve and pump seal failure patterns across Bosch platforms.
General information only. Internal layout and access panels differ between Bosch models and markets. Unplug and shut off the water before any work, and use a qualified technician if the machine is hard-wired or under warranty.