The short answer
- Most likely: the filter and sump are blocked with food and grease.
- Second: the drain hose is kinked, or the sink spigot / disposal connection is blocked.
- Third: the non-return valve is stuck, or the drain pump has failed.
- Note: a shallow pool in the very bottom of the sump is normal on many machines — the question is whether the load is wet and the filter is swimming.
First: is it actually a fault?
Many dishwashers deliberately leave a little water below the filter to keep the pump seal wet. If the water is only in the recessed sump and the dishes came out clean and dry, nothing is wrong.
It is a fault when:
- The water is above the filter or covering the bottom of the tub.
- The dishes are wet, greasy or gritty at the end of the cycle.
- The machine stops mid-cycle, or shows a drain code.
- The water smells, or returns after you empty it.
Empty it safely
- Unplug the machine and turn off the water tap under the sink.
- Scoop the water into a bowl with a cup, then sponge the sump dry.
- Do not tip the machine. Water runs into the insulation and the base, which is exactly how a small blockage becomes an E15 leak code.
The check order
- Filter assembly. Remove the lower basket, twist out the cylindrical filter and lift the flat filter. Rinse both. This is the fix in most households.
- Sump and pump cover. With the water out, look into the sump. Remove the pump cover where the model has one and check for glass, a bottle cap or a piece of cutlery.
- Non-return valve. A flap in the sump area that stops water flowing back. Debris holding it shut blocks the drain; the part is cheap.
- Drain hose. Follow it behind the cabinet. Look for a kink, a crush, or a hose that loops low and traps water.
- Sink spigot or disposal. Where the hose joins the plumbing, grease and food block the connection. On a disposal connection, run the disposal and check the knockout plug was removed at installation — a classic cause of a dishwasher that has never drained properly.
- Pump. Start a drain cycle and listen. Humming with no flow is a jammed impeller; silence is electrical.
- Air gap (where fitted). In some markets an air gap on the sink deck can block. Check it if the installation has one.
What the pattern tells you
| Pattern | Likely cause |
|---|---|
| Water every cycle, dishes gritty | Filter blocked |
| Water drains slowly, then stops | Hose or spigot partly blocked |
| Water returns after emptying | Non-return valve stuck open, or a shared drain backflowing |
| No water movement at all, pump hums | Jammed impeller or glass in the pump |
| Pump silent | Electrical fault — connector, pump or control |
| Water on the floor too | Leak rather than a drain fault — stop using it |
Codes that come with it
Bosch calls a blockage E24 and a pump failure E25; other brands use their own letters. The Bosch E24 / E25 guide and the full Bosch list cover the numbered side; the checks above apply to every brand because the drain path is the same in all of them.
Repair or replace
Cleaning is free. A non-return valve or a hose is cheap. A drain pump is a moderate part and a reasonable repair. If the machine is also leaking into its base, the combined repair is the point where repair or replace becomes the honest question.
Frequently asked questions
Can I just run the cycle again to clear it?
Sometimes a second drain clears a light blockage, and it is a reasonable first try. If the water stays at the same level, stop and clean the filter.
Why does it drain into the sink and come back up?
Because the sink trap or the shared drain is blocked, and the dishwasher's discharge has nowhere to go. Clear the sink plumbing, not the dishwasher.
Is a little water in the filter area normal?
Yes, below the filter. Water above the filter, or covering the tub floor, is not.
Sources
- Manufacturer support documentation for dishwasher drain faults and filter cleaning: Bosch, Samsung, LG and Whirlpool consumer support sections, accessed 16 November 2026.
- Installation documentation on drain hose routing, spigot connection and air gaps.
- Editorial review against the parts trade: the blockage points that account for most drain call-outs.
General information only. Filter design and plumbing connections vary by brand and market. Unplug and turn off the water before interior work, and use a qualified plumber for connections under the sink you cannot reach safely.