Appliance Error Code Guide Codes, causes & fix order
Dishwashers · Bosch

Bosch Dishwasher Error Codes (Full List)

Bosch codes are numbered by function, so the list itself is a map of the machine: heating, filling, draining, sensing, and the low-voltage side that ties them together.

Checked against Bosch support documentation Updated 16 November 2026 11 min read

The short answer

  • E09 — heating fault. Dishes come out cold and wet.
  • E15 — water in the base tray: a leak, not a blockage.
  • E17 — fill fault: the machine is not taking water in time.
  • E22 — filter or flow-sensor fault on models that use it.
  • E24 / E25 — drain blockage / drain pump not running.
  • Reset: most models clear a code with a button combination; none of them fix the cause.

The code map

Bosch's numbering is broadly functional, and knowing the bands saves time even before you find the exact definition for your model:

CodeSystemWhat you noticeFirst check
E01 / E02Temperature sensor / NTC circuitCycle stops early, water temperature wrongSensor connector, sensor resistance
E09HeatingDishes cold and wet; wash runs but never heatsHeater continuity, heater relay, temperature sensor
E15Leak detection (base float)Machine stops, water in the base trayDoor seal, internal hoses, pump seals
E17Fill / water inletNo water, or the fill times outTap, inlet hose, inlet filter screen, water valve
E22Filter / flow sensorPoor wash results, code after a few minutesFilter assembly, flow sensor on models fitted with one
E24Drain path blockedStanding water in the tubFilter, sump, non-return valve, hose, spigot
E25Drain pumpStanding water, pump silentPump impeller, connector, pump supply
E27Supply voltage / power moduleMachine dead or stopping randomlySocket and supply; then power module

Not every Bosch series uses every code, and the flexible-zone and fully integrated ranges add functions that older platforms did not have. The list above covers the codes owners actually meet; the model's own booklet or the rating-plate model number on Bosch's support site gives the definitive list.

Reading the code by group

Cold and wet dishes: the heating group

E09 and the sensor codes are the reason a dishwasher "works" but leaves the load cold and dripping. The heater is a simple resistive element; the usual failures are the element itself, its relay on the control, or a temperature sensor reading that stops the control from calling for heat.

No water: the fill group

E17 is the fill timeout. Check the tap under the sink first — it is turned off more often than anyone admits — then the inlet hose, the small mesh filter at the inlet valve, and the valve itself. Low mains pressure produces the same code as a blockage.

Water that will not leave: the drain group

E24 is a blockage and E25 is the pump. Clean the filter and the sump, check the non-return valve, then look outside the machine at the hose and the sink spigot. Only then suspect the pump.

Water where it should not be: E15

E15 is the only code in the list that is almost always telling the truth about something else. The float in the base tray lifts because water reached it, and the job is to find the leak — door seal, internal hose, inlet valve, sump or pump seals.

Everything electrical: E27 and the module codes

Supply faults look dramatic and are often boring: a socket on a shared circuit, an extension lead, a voltage dip when a large appliance starts. Check the supply before authorising a power module.

Unplug and turn off the water before any internal check. The base area and the sump hold water even after a drain, and a dishwasher on a shared circuit can be live at the control even when the display is blank.

Resetting a Bosch code

Most Bosch dishwashers clear a displayed code with a reset sequence — often holding the start button for a few seconds, or a two-button combination — and some clear it when the door is opened and closed after power is restored. The sequence is in the manual for your series.

What a reset does not do is fix anything. If the code was caused by a leak, a blockage or a heating fault, it returns — usually in the same part of the same cycle, which is itself useful information.

Repair or replace

Filters, hoses and door seals are cheap. Heaters, pumps and sensors are moderate. A control module is the expensive end and only worth it on a machine that is otherwise sound and modern. Repair or replace puts the decision in numbers you can check against your own quote.

Frequently asked questions

Are Bosch codes the same across Series 2, 4, 6 and 8?

Mostly, for the core functions — heating, filling, draining and leaks. The higher series add functions and can show codes the entry series never displays.

The display shows a code and a letter as well — what is that?

Some models show a code with an additional letter or a flashing symbol indicating the phase (fill, wash, drain). The number is the fault; the extra character tells you where in the cycle it happened.

Do I need the model number to order a part?

Yes. It is printed on the inner edge of the door or on the side of the tub, in a format like SMs or SMS followed by digits. Bosch spares are matched to that number, not to the marketing name.

Sources

  1. Bosch Home Appliances Support — dishwasher error code guidance and manuals by model number (bosch-home.com support sections), accessed 16 November 2026.
  2. Bosch service documentation on fill, drain, heating and leak-detection circuits.
  3. Editorial review against the parts trade: the codes seen most often in service and the parts that resolve them.

General information only. Codes, access panels and part locations differ between Bosch series and markets. Confirm against your model's documentation, unplug before interior work, and leave power-module and hard-wired work to a qualified technician.