Appliance Error Code Guide Codes, causes & fix order
Washers · Electrolux

Electrolux Washing Machine Error Codes

Electrolux, AEG and Westinghouse share one code system, and it is the most logical in the industry: the first two digits name the system, the last digit narrows the fault. Learn five numbers and you can read almost any code these machines display.

Checked against Electrolux support documentation Updated 17 November 2026 9 min read

The short answer

  • E10 fill · E20 drain · E30 pressure sensor · E40 door · E50 motor · E60 heating.
  • EF0 covers leaks, excess foam and imbalance; EH0 covers the power supply.
  • E10 and E20 are the two you can fix yourself: taps, screens, filter, hose.
  • E50 and E60 need a technician — motor drive and heating circuits.

The code families

Code familySystemFirst checkDIY?
E10, E11, C1Water supplyTap open, hose straight, inlet screen cleanYes
E20, E21, C2DrainingPump filter, drain hose, standpipeYes
E30Water pressure sensorHose to the sensor, then the sensorPartly
E40, E41Door lockDoor closed, seal clear, strikerPartly
E50MotorBelt, drum free to turnNo
E60, E61, E62HeatingDoes a cold wash complete?No
EF0 — EF5Leak, foam or imbalanceDetergent amount, load balance, water underneathYes
EH0Power supplySocket, voltage, extension leadYes

E10: it will not fill

  1. Open the taps fully. Many front loaders fill from cold only, so the cold tap is the one that matters.
  2. Check the inlet hoses behind the machine for kinks or a crushed section.
  3. Clean the inlet screens. Turn the taps off, unscrew the hose at the machine, lift out the mesh and rinse it.
  4. Check the household pressure at another tap. Low pressure across the house is not the machine's fault.
  5. Look at the fill valve if all four are good — a valve that does not open needs replacing.

E20: it will not drain

  1. Unplug the machine and let any hot water cool before opening the filter.
  2. Open the small flap at the bottom front, drain the emergency hose into a tray, then unscrew the pump filter.
  3. Clean the filter and check the impeller behind it turns. Coins, hair clips and bra wires are the usual culprits.
  4. Check the drain hose for kinks and confirm it is not pushed too far into the standpipe.
  5. Check the standpipe or sink spigot drains freely. A slow sink backs water into the machine, which reports it as its own fault.
Water can be hot. A machine that stopped mid-wash may hold water at 60°C or more. Let it cool before draining, and put a towel down — several litres come out at once.

E40 and E50: door and motor

E40 is almost always mechanical before it is electrical: a sock in the seal, a door that needs a firmer push or a bent striker. If those are fine, the lock needs testing, and the machine will keep the door locked while it holds water — that is the lock working, not a second fault.

E50 is the motor drive. On belt-drive machines, check the belt first: a thrown or worn belt gives exactly this code. With the machine unplugged, turn the drum by hand — if it is stiff or grinding, the fault is mechanical and the motor is innocent.

E60 and the heating circuit

E60 means the water is not heating as expected. The useful diagnostic test is simple: run a cold programme. If it completes normally, the machine and its motor are fine and the fault is in the heater, its thermostat or the pressure switch that tells the board there is enough water to heat safely. Electrolux advises a power reset first and a service visit if the code returns — this is not a part to change blind.

What each family points to

CodeLikely partNote
E10Inlet screen, hose, fill valveScreen and hose first almost every time
E20Filter, drain hose, pumpPump only after the filter and hose are proven clear
E30Pressure sensor or its hoseCheck the hose for sludge
E40Door lock, striker, harnessCheck the seal and striker before the lock
E50Belt, motor, drive boardBelt first on belt-drive models
E60Heater, thermostat, sensorConfirm with a cold-wash test

Repair or replace

E10 and E20 are usually free or cheap. E50 and E60 are the point where the arithmetic matters, especially on an older machine — repair or replace sets out the comparison, and what a washer repair involves explains what a technician's quote covers.

Frequently asked questions

My machine shows a code with a dash, like E:20 — is that different?

No. Newer displays separate the letters and digits with a colon or a space. Read the first two characters as the system.

Does AEG use the same codes?

Largely, yes — the platforms are shared. Confirm against your model's manual, because a few variants differ.

What is the most common Electrolux code overall?

E20. Blocked filters and kinked drain hoses account for most of them, and most are fixed without a part.

Sources

  1. Electrolux support — "Washing machine displays an error code: causes and solutions", listing the E10, E20, E30, E40, E50, E60, EF0 and EH0 families, accessed 17 November 2026.
  2. Electrolux support article on the E60 heating fault and the recommended reset procedure.
  3. Editorial review against the service trade: drain filter and inlet screen blockage rates on Electrolux/AEG platforms.

General information only. Codes and part locations differ by model and market. Confirm against your machine's documentation and unplug before opening any panel.