The short answer
- E18 / F18 — will not drain. Clean the pump filter and the drain hose; most cases end there.
- E17 / F17 — will not fill. Tap, hose, inlet screen, then the valve.
- E16 / F16 — door open. Close it firmly, check the seal, then the lock.
- E23 / F23 — AquaStop has triggered. There is water in the base; find the leak.
The codes
| Code | System | What it means | DIY? |
|---|---|---|---|
| E16 / F16 | Door | Door not detected as closed | Yes — seal and latch |
| E17 / F17 | Water supply | Not filling fast enough | Yes — tap, hose, screen |
| E18 / F18 | Drain | Not draining in time | Yes — filter and hose |
| E19 / F19 | Heating | Heating time exceeded | No — element or sensor |
| E20 / F20 | Heating | Unexpected heating | Reset, then service |
| E21 / F21 | Motor | Drum not turning | Check the drum by hand first |
| E23 / F23 | Leak protection | AquaStop triggered | No — find the leak |
| E25–E28 | Sensors | Turbidity, pressure or flow sensor | No |
| E56 | Communication | Internal communication error | No |
Codes can appear as E18, F18 or E:18 depending on the generation and the display. Read the number, not the letter.
E18: the one that pays for this article
- Switch off and unplug, and let hot water cool before opening anything.
- Open the small flap at the bottom front and place a shallow tray and a towel.
- Pull out the emergency drain hose, remove its plug and drain the water, then refit the plug.
- Unscrew the pump filter slowly anticlockwise — more water will come. Clean it, and check the housing with a torch for coins and hair clips.
- Turn the impeller behind the filter by hand. It should turn with light resistance; if it will not, hook out the obstruction.
- Refit the filter firmly — a cross-threaded filter leaks and produces an E18 that never clears — then check the drain hose for kinks and the standpipe for a blockage.
E17 and the fill path
Bosch specifies a minimum flow rate for a fill. If the machine cannot get water at that rate, it stops. The order is: tap fully open, hose not kinked, inlet screen cleaned, household pressure normal. On models without a numeric display, the same fault shows as a tap symbol or a flashing tap light.
E21 and the drum
E21 means the drum did not turn as commanded. Before suspecting the motor, unplug the machine and turn the drum by hand. Free and smooth means the fault is electrical; stiff, grinding or blocked means a jammed item, a worn bearing or a broken belt on belt-drive models. Overloading produces the same code on some machines.
E23: AquaStop
Bosch's AquaStop system combines a leak-protection valve in the inlet hose with a float sensor in the base. When water reaches the base, the machine stops and E23 is displayed. The valve may also cut the supply permanently, which is why the machine refuses to fill afterwards.
Look for the source: door seal, detergent drawer, inlet connections, pump housing, internal hoses. Do not simply dry the base and restart — the leak is still there, and a repeat flood inside a kitchen is worse than a service call.
What each code points to
| Code | Part | Notes |
|---|---|---|
| E16 | Door lock or striker | Check the seal for trapped clothing first |
| E17 | Inlet screen, hose, valve | Screen is the usual cause |
| E18 | Filter, hose, pump | Pump only after the first two are clear |
| E19 / E20 | Heating element, thermostat, sensor | Confirm with a cold programme |
| E21 | Belt, motor, drive board | Turn the drum by hand first |
| E23 | AquaStop valve, base sensor, internal hose | Find the leak; do not just reset |
Repair or replace
E17 and E18 are free-to-cheap fixes. E19, E21 and E23 are service repairs, and on a machine that is already ten years old the comparison in repair or replace is the honest way to decide.
Frequently asked questions
Why does E18 return straight after I clean the filter?
The filter is cross-threaded, the housing seal is damaged, or the pump impeller is jammed behind the filter. Check all three before ordering a pump.
Can I use the machine with E16 if the door looks shut?
No. The machine will not fill or spin, and forcing the door can break the hinge.
Does a Bosch washer need a special detergent for E25?
The turbidity sensor code is about the sensor reading, not the detergent — but excessive foam from hand-wash detergent will trigger sensor and leak codes on these machines.
Sources
- Bosch Home — "Laundry troubleshooting: washer error codes" (E16/F16 through E28/F28), accessed 17 November 2026.
- Bosch service guidance on E17 inlet flow, E18 drain and E23 AquaStop, including the pump filter procedure.
- Editorial review against the parts trade: filter and pump failure patterns on Bosch front loaders.
General information only. Codes and component locations differ by model and market. Confirm against your machine's documentation and unplug before opening any panel.