Appliance Error Code Guide Codes, causes & fix order
Dishwashers · LG

LG Dishwasher Error Codes

LG uses two-letter codes rather than numbers, and one of them — AE or E1 — appears for a reason owners rarely expect: too much detergent, or a bottle of dishwashing liquid used in place of tablets.

Checked against LG support documentation Updated 17 November 2026 8 min read

The short answer

  • IE — water in. Valve, hose, supply.
  • OE — water out. Filter, hose, hose height.
  • AE / E1 — leak in the base pan. Find the leak, dry the pan, reset.
  • bE — oversudsing. Wrong detergent or too much of it.
  • HE / tE — heater or temperature sensor. Service.

The codes

CodeMeaningFirst check
IEWater inlet errorSupply valve, kinked hose, water outage
OEWater outlet errorFilter, drain hose, hose end height
AE / E1 / RELeak — float switch activatedDetergent amount, level, door gasket, spray arms
bEBubble / oversudsing errorDishwashing liquid or excess powder
HEHeater faultService
tETemperature sensor faultService
FEExcess water suppliedInlet valve, level sensor

IE: no water in

  1. Check the kitchen tap — is there water at all?
  2. Open the sink cabinet and find the valve on the dishwasher inlet. Turn it anticlockwise to open. Also check the shut-off valve above it.
  3. Check the inlet hose for kinks or a squash where it passes behind the cabinet.
  4. Look at the inlet screen at the machine connection for grit.
  5. On a new installation, ask the installer whether both valves were opened — this is the most common cause on a machine less than a week old.

OE: water will not leave

  1. Wait thirty minutes after a cycle before touching the filter — the tub is hot.
  2. Remove the lower rack, turn the filter handle anticlockwise and lift out the assembly.
  3. Separate the inner and stainless filters and wash both. Refit and turn clockwise until it clicks.
  4. Check the drain hose for kinks and make sure its end sits at least 30 cm above the floor. Too low and it siphons; too deep in a standpipe and it air-locks.
  5. Force a drain if your model supports it — power on and hold Start for three seconds — and watch the water level.

Water standing just below the filter after a cycle is normal: it traps sewer gas. Water above the filter is a fault.

AE / E1: the leak code

This code means water reached the float switch in the base pan. LG's own guidance puts the causes in a useful order: too much detergent or the wrong type causing excessive suds, a machine that is not level, a dirty or damaged door gasket, blocked spray arms, or water poured into the Heat Dry blower instead of the water softener.

To clear it, switch off at the breaker, remove the kick plate, dry the base pan, and leave it open for a day or two if the water has not evaporated. Then run an empty cycle with a single tablet. If the code returns with correct detergent and a level machine, it needs service.

Turn off the breaker, not just the panel, for a leak code. A built-in dishwasher holds water above electrical components in its base. Do not pull a plumbed-in machine forward without closing the supply and disconnecting the drain.

bE: the bubble code

Dishwashing liquid is concentrated and foams far more than dishwasher detergent. The machine detects the foam and stops to protect itself. Run a rinse cycle with no detergent, wipe out any foam, and switch to tablets or powder measured to the dispenser lines. Two tablets in one load does the same thing.

Repair or replace

IE and OE are usually a valve position or a filter clean. AE is a leak you may be able to fix with a gasket clean and a level machine. HE, tE and repeated leaks after correct use are service items — compare against repair or replace before authorising a board.

Frequently asked questions

The machine runs but dishes come out wet — is that a code?

No. Check the rinse aid, the hot water supply temperature and whether the Heat Dry setting is on. A blocked filter also leaves dishes wet and gritty.

OE appears only on the intensive cycle — why?

That cycle uses the most water and the longest drain. A partly restricted filter or hose shows up there first.

Can I reset AE by unplugging?

The display clears, but if the base is still wet the code returns when the float lifts again. Dry the base properly.

Sources

  1. LG support — dishwasher guide to error codes (IE, OE, FE/AE, tE, HE, bE), US support library, accessed 17 November 2026.
  2. LG support article on the AE and E1 leak codes and drying the drain pan.
  3. Editorial review against the service trade: disposal-less installs, hose height faults and oversudsing complaints.

General information only. Code wording and base-pan access differ by model. Confirm against your machine's manual and isolate the power before opening the base.