Appliance Error Code Guide Codes, causes & fix order
Dishwashers · Samsung

Samsung Dishwasher Error Codes

Samsung's dishwasher codes are short and consistent: the 4 family is water in, the 5 family is water out, LC is a leak and H is heat. Once you know that, the display reads like a sentence — and two of the four are yours to fix.

Checked against Samsung support documentation Updated 17 November 2026 9 min read

The short answer

  • 4C / 4E — no water or not enough. Tap, hose, inlet filter.
  • 5C / 5E / SC — will not drain. Filter, sump, drain hose.
  • LC / LE — leak detected in the base. Stop and find it.
  • HC / HE — heater or temperature fault. Power cycle, then service.

The codes

CodeMeaningFirst check
4C / 4EWater supply errorSupply valve open, hose not kinked, inlet filter clean
5C / 5E / SE / SCDrain errorFilter, sump, drain hose, disposal cap
LC / LELeakage detectedDoor seal, hoses, dispenser, pump; water reflector on Waterwall models
HCHigh temperature heater errorPower cycle at the breaker, then a normal cycle
HEHeater errorRun a normal cycle empty; service if it returns
1E / IEClogged filter (Waterwall) or high temperature (rotary)Clean the filter first
Temperature sensor faultReads incorrectlyService

Models without a digital display show the same faults as blinking light patterns. Note which lights flash and in what order, and compare with the manual — that is the code.

4C: it will not take water

  1. Open the supply valve fully. It is usually under the sink, and installers often leave it part-closed.
  2. Check the inlet hose for kinks behind the cabinet.
  3. Clean the inlet filter at the connection to the machine — grit after a pipe repair is common.
  4. Check the household supply at the kitchen tap, and whether the machine was recently installed or moved.
  5. Consider the hose type. Samsung advises against FloodSafe hoses on some models because the safety valve restricts flow enough to trigger this code.

5C: it will not drain

  1. Remove the lower rack and take out the filter assembly — turn the handle anticlockwise and lift.
  2. Clean the inner and outer filters under running water, and check the sump with a torch for glass and food debris.
  3. Check the drain hose for kinks where it leaves the machine and where it enters the standpipe or disposal.
  4. If it drains into a disposal, make sure the plug has been removed from the disposal nipple. This is the single most common cause after a new installation.
  5. Force a drain if your model supports it, and watch whether water actually leaves.

LC: leakage

An LC code means the base sensor has seen water. Samsung's documentation is clear that the machine will keep trying to drain and may not switch off, so close the supply and cut the power at the breaker.

Look for the source at the door seal (clean it and check for tears), the inlet and drain connections, the dispenser, and the pump housing. Excess detergent or hand-washing liquid produces so much foam that water escapes past the door — that is a real cause, not a guess. On Waterwall models a blocked water reflector can also set it. Remove any standing water from the base before restarting, and do not simply reset the code.

Water plus mains voltage. For any leak code, switch the machine off at the breaker, not just on the panel, before pulling it forward or opening the base. A built-in dishwasher full of water is heavy — two people or a technician.

HC and HE

Both are heating faults. HC means the temperature inside rose higher than expected; HE means the heater or its temperature sensing is not behaving. Samsung's own advice is to empty the machine, power cycle at the breaker for about thirty seconds, and run a normal cycle with detergent. If the code returns, it is a service item — the heater, thermistor or board.

Repair or replace

Filter and drain faults are free to fix and account for most codes. A leak may be a seal or a hose. A heater or board repair is the expensive end, and on a machine older than eight years the comparison in repair or replace is worth doing before authorising it.

Frequently asked questions

Why is 4C worse after I fitted a new hose?

The new hose may be a FloodSafe type that restricts flow, or its washer may be blocking the inlet. Refit with the supplied seal and check for full flow into a bucket.

Standing water below the filter — is that a fault?

A small amount always remains to trap sewer smells. Water above the filter level after a cycle is a drain fault.

Can I use dishwashing liquid if I run out of tablets?

No. It foams, and the foam sets leak codes and can overflow the base. Use nothing rather than liquid.

Sources

  1. Samsung support — "Dishwasher is displaying an error code" and the information-code lists for the US, UK, Canada and Australia, accessed 17 November 2026.
  2. Samsung support article on the 5C/5E, 4C/4E and LC/LE water-related codes, including the drain filter procedure.
  3. Editorial review against the service trade: disposal plug and FloodSafe hose installation faults.

General information only. Code wording and panel behaviour differ by model and market. Confirm against your machine's manual and switch off at the breaker for any leak.